Home › Cost guides › Alabama › Anniston & Oxford, AL

30×40 Pole Barn Cost in Anniston & Oxford, AL (2026)

A 30×40 pole barn in Anniston & Oxford, AL costs about $39,264 turnkey in 2026 ($32.72 per sq. ft.). Here's the itemized breakdown of materials, site prep and labor, using local crew rates.

Materials-Only Kit
$15,914
Delivered lumber, trusses, metal panels & hardware
= Rows 3–7 below, materials only
Concrete Slab & Site Prep
$8,749
Grading, forms, rebar & poured concrete floor
= Rows 1–2 below, installed price
Turnkey Installed Total
$39,264
$32.72 per sq. ft.
Complete build with a local licensed crew, materials & slab
= All rows below, installed price

Prices updated Oct 2026

A fair bid from a local builder in Anniston & Oxford, AL should land between $33,374 and $47,117, about 15% below to 20% above this estimate. Quotes for the same building can vary widely, so get 3 quotes on the same spec. If one is outside this range, ask what it includes or leaves out.

Reference wind speed for this area: not listed here. Wind values here are reference figures for pricing. Confirm the design wind speed with your local building department or engineer.

Estimate only. Actual prices vary. No guarantee or warranty. Use as a guide only. Read the full disclaimer

Itemized cost breakdown

#ItemQuantityMaterialsLaborInstalled
1Site grading & building padLaser-leveled pad 2 ft past the walls, compacted fill1,496 sq ft$643$891$1,841
24" standard concrete slab3,500 PSI ready-mix, #4 rebar 18" grid, vapor barrier, forms15.9 cu yd$3,262$2,495$6,908
36×6 treated posts, girts & framing lumber18 posts × 16 ft (.60 CCA ground-contact), 2×6 girts at 2 ft incl. gable girts, 2×8 treated skirt board18 posts + 888 lf$3,368$3,267$7,962
430' engineered roof trusses & purlins11 trusses at 4 ft on center, standard wind allowance, 2×4 purlins at 2 ft (18 rows)11 trusses + 756 lf$3,346$1,901$6,296
529-ga metal roof & wall panels + trimPainted steel panels, ridge cap, corner/door/base trim, closures31.5 squares$4,203$1,792$7,194
6Overhead & walk doorsDetails in the spec sheet🔒 Included in $19 spec sheet——🔒
7Screws, hardware & condensation barrierDetails in the spec sheet🔒 Included in $19 spec sheet——🔒
8Permit, stamped drawings & deliveryDetails in the spec sheet🔒 Included in $19 spec sheet——🔒
Turnkey total$21,127$11,593$39,264

Prices use 2026 material costs and typical local crew rates. Site work, custom options and material price swings can move your final price.

$19 one-time

Builder Spec Sheet & Shopping List

A sheet for comparing 3 builder bids line by line, and a builder-ready spec so every builder prices the same building. Plus the same line items as this page in an editable Excel file and a PDF (spec, quantity, materials, labor and installed price) and a permit and site-prep checklist. It also includes a full itemized takeoff: panel cut lengths, trim, a fastener schedule, lumber counts and concrete yards, with the spacing rule and source for each line. 30-day money-back.

Get my spec pack
Free

Request free local quotes

Tell us your ZIP and timeline. We're still adding builders in your area; we'll connect you when one is available. No cost, no obligation.

Request free quotes

Common questions

How much does a 30×40 Pole Barn cost in Anniston & Oxford, AL?

About $39,264 fully built by a local crew in 2026, or roughly $15,914 for the materials kit alone. Most fair bids land between $33,374 and $47,117.

What drives the price up or down?

Site prep (slope, soil, driveway access), floor choice, doors and insulation, and local labor rates. Lumber and steel prices also move a few percent a year.

Do I need a permit?

Permit requirements vary by county and city. Many unincorporated areas of Alabama don't enforce a building code, while cities and some counties do. Check with your county or city building office before you build.

How do I make sure I'm getting a fair quote?

Get at least 3 itemized bids for the same spec. Compare them line by line against this breakdown and ask about anything far above or below it.

Related cost guides