Free cost calculator

Home › Cost guides › North Carolina › Raleigh, NC

40×60 Pole Barn Cost in Raleigh, NC (2026)

A 40×60 pole barn in Raleigh, NC costs about $71,508 turnkey in 2026 ($29.80 per sq. ft.). Here's the itemized breakdown of materials, site prep and labor, using local crew rates.

Try another size or city Free. The numbers below update instantly.

40×60 ft, 14 ft walls (2,400 sq. ft.)

Get my spec sheet ($9.99)Change size, city or options (free calculator)
What does the $9.99 spec sheet add? ↓
Materials-Only Kit
$26,346
Delivered lumber, trusses, metal panels & hardware
= Rows 3–7 below, materials only
Concrete Slab & Site Prep
$18,184
Grading, forms, rebar & poured concrete floor
= Rows 1–2 below, installed price
Turnkey Installed Total
$71,508
$29.80 per sq. ft.
Complete build with a local licensed crew, materials & slab
= All rows below, installed price

Prices updated Oct 2026

A fair bid from a local builder in Raleigh, NC should land between $60,782 and $85,810, about 15% below to 20% above this estimate. Quotes for the same building can vary widely, so get 3 quotes on the same spec. If one is outside this range, ask what it includes or leaves out.

Reference wind speed for this area: 115 mph (local building-department figure, not a design value). Wind values here are reference figures for pricing. Confirm the design wind speed with your local building department or engineer.

Estimate only. Actual prices vary. No guarantee or warranty. Use as a guide only. Read the full disclaimer

Itemized cost breakdown

#ItemQuantityMaterialsLaborInstalled
1Site grading & building padLaser-leveled pad 2 ft past the walls, compacted fill2,816 sq ft$1,250$1,803$3,664
24" standard concrete slab3,500 PSI ready-mix, #4 rebar 18" grid, vapor barrier, forms31.7 cu yd$6,722$5,378$14,520
36×6 treated posts, girts & framing lumber26 posts × 18 ft (.60 CCA ground-contact), 2×6 girts at 2 ft incl. gable girts, 2×8 treated skirt board26 posts + 1,496 lf$5,631$7,042$15,208
440' engineered roof trusses & purlins16 trusses at 4 ft on center, standard wind allowance, 2×4 purlins at 2 ft (24 rows)16 trusses + 1,488 lf$6,721$4,097$12,982
529-ga metal roof & wall panels + trimPainted steel panels, ridge cap, corner/door/base trim, closures56.3 squares$7,542$3,457$13,199
6Overhead & walk doorsDetails in the spec sheet🔒 Included in $9.99 spec sheet——🔒
7Screws, hardware & condensation barrierDetails in the spec sheet🔒 Included in $9.99 spec sheet——🔒
8Permit, stamped drawings & deliveryDetails in the spec sheet🔒 Included in $9.99 spec sheet——🔒
Turnkey total$36,084$23,505$71,508

The totals above already include every row, including the 🔒 rows. The $9.99 spec sheet lists them item by item with quantities.

What do these terms mean?
  • Turnkey total: materials, site work and a crew to build it, all in one number.
  • 29-ga metal: the steel panel thickness (a lower gauge number is thicker).
  • .60 CCA posts: treated posts rated to go in the ground.
  • Purlins and girts: boards across the roof and walls that the metal panels screw into.
  • PSI: a concrete strength rating.
  • #4 rebar: ½-inch steel bar laid in a grid inside the concrete.
  • Vapor barrier: plastic sheeting under the slab that keeps ground moisture out.
Adjust this estimate in the free calculatorSave a free project request

Prices use 2026 material costs and typical local crew rates. Site work, custom options and material price swings can move your final price.

$9.99 one-time

Builder Spec Sheet & Shopping List

A sheet for comparing 3 builder bids line by line, and a builder-ready spec so every builder prices the same building.

  • Every line item on this page, including the 🔒 rows, in an editable Excel file and a PDF (spec, quantity, materials, labor and installed price)
  • A permit and site-prep checklist
  • A full itemized takeoff: panel cut lengths, trim, a fastener schedule, lumber counts and concrete yards, with the spacing rule and source for each line

30-day money-back.

Get my spec sheet ($9.99)
Free

Save a free project request

Tell us your ZIP and timeline. We aren't connecting requests with builders yet. No cost, no obligation.

Save my request

Common questions

How much does a 40×60 Pole Barn cost in Raleigh, NC?

About $71,508 fully built by a local crew in 2026, or roughly $26,346 for the materials kit alone. Most fair bids land between $60,782 and $85,810.

What drives the price up or down?

Site prep (slope, soil, driveway access), floor choice, doors and insulation, and local labor rates. Lumber and steel prices also move a few percent a year.

Do I need a permit?

Permit requirements vary by county and city. Check with your county or city building office before you build.

How do I make sure I'm getting a fair quote?

Get at least 3 itemized bids for the same spec. Compare them line by line against this breakdown and ask about anything far above or below it.

Related cost guides